1. The science behind the images¶
1.1 Why radar sees what it sees¶
A radar sends a pulse and times its return. Distance comes from time, as \(R = ct/2\), where \(c\) is the speed of light and the 2 accounts for the trip out and back. Sentinel-1 uses C band: a frequency of 5.405 GHz, which is a wavelength of \(\lambda = c/f \approx 5.5\) cm. Features much smaller than this look smooth to the radar, which is why calm water and tarmac act like mirrors.
The sensor looks sideways, not straight down. If it looked straight down, two points at equal distance either side would return together and could not be told apart. Looking sideways at about 29 to 46 degrees in this mode solves that, and also causes the distortions described below.
1.2 What backscatter is¶
The radar equation says how much power returns:
Here \(P_t\) is power sent, \(G\) antenna gain, \(R\) range and \(\sigma\) the radar cross-section of the target. Everything but \(\sigma\) is known about the instrument and geometry, so it can be removed by calibration. For a surface, \(\sigma\) is divided by the ground area to give \(\sigma^0\) (sigma nought), a dimensionless ratio that can be compared between places and dates.
1.3 What a decibel is¶
Backscatter spans many orders of magnitude, from about 0.001 for calm water to above 10 for a building’s corner. A logarithmic scale fits this on a readable range:
| Linear | dB | Meaning |
|---|---|---|
| 0.001 | \(-30\) | A thousandth of the reference |
| 0.01 | \(-20\) | A hundredth |
| 0.1 | \(-10\) | A tenth |
| 1 | 0 | Equal to the reference |
| 2 | \(+3\) | About double |
| 10 | \(+10\) | Ten times |
Decibels are ratios, so a difference in dB is a ratio in power. A change from \(-10\) to \(-13\) dB means half the power returned, wherever it happens on the scale. Negative values are normal and do not mean negative energy: they mean less than the reference.
Why averaging in dB is wrong.¶
Take two pixels at \(-30\) and \(0\) dB. Their mean in dB is \(-15\) dB. In linear units, the mean of 0.001 and 1 is 0.5005, which is \(-3\) dB. The dB mean is lower by 12 dB, a factor of about 16 in power, because a logarithm gives the dim pixel too much weight. So we average in linear power, as mean_db() does in Chapter 2. Over a year of London scenes this matters most at strong targets, whose returns vary.
1.4 Polarisation: what VV and VH tell us¶
The radar’s wave oscillates in one plane. Sentinel-1 sends vertically (V) and receives both V and horizontal (H). Each surface changes this differently:
| Mechanism | What happens and where |
|---|---|
| Surface scattering | Rough ground reflects some energy back, mostly keeping polarisation, so VV is above VH |
| Volume scattering | Repeated scattering among leaves and branches scrambles polarisation, so VH rises |
| Double bounce | Ground and wall form a corner that returns energy strongly, so VV is very high, as in cities and flooded forest |
| Specular reflection | A smooth surface reflects energy away, so both are low, as on calm water |
The ratio VV minus VH (in dB, which is a ratio in linear terms) separates these partly, which is why it serves as the third band in our colour image.
1.5 Speckle¶
What it is.¶
A pixel holds many scatterers. Their returns add as waves with random phases, sometimes reinforcing and sometimes cancelling. So uniform ground looks grainy, even with a perfect instrument. Viewed the same way, the same ground gives the same grain, which makes it a form of interference and not random instrument noise.
The model.¶
Speckle is multiplicative: observed intensity \(I\) is the true backscatter \(\sigma^0\) times a random factor \(n\) with mean 1:
Multiplicative means brighter areas have larger swings in linear units, and a logarithm turns these into a roughly constant spread. \(L\) is the number of looks, or independent samples averaged. It can be estimated from a uniform area as the equivalent number of looks:
Measured here.¶
Over the most uniform 300 m patch near central London, ENL is 4.4 in one scene and 20.9 in the mean of 149 scenes. The increase is less than 149-fold, because the patch is not perfectly uniform and because real changes through the year remain. This also suggests a limit: averaging removes speckle at the cost of time detail, and filters such as Lee or Refined Lee remove it at the cost of spatial detail.
1.6 What has been done to the data¶
The Earth Engine collection COPERNICUS/S1_GRD holds Ground Range Detected scenes, already processed as follows:
-
Orbit file: precise position of the satellite.
-
GRD border noise removal: low-value strips at scene edges.
-
Thermal noise removal: the instrument’s own noise.
-
Radiometric calibration: digital numbers to \(\sigma^0\).
-
Terrain correction: moved to map position with a digital elevation model.
-
Conversion to dB.
It has not had speckle filtering or radiometric terrain flattening, so slopes facing the satellite stay bright. “Detected” also means phase has been discarded, so these scenes cannot be used for interferometry; heights and motion need the single look complex (SLC) product, or ready-made interferograms such as ASF HyP3 for Sentinel-1 and NISAR’s GUNW.
1.7 Three distortions of mountains¶
Because radar measures distance, tall things shift towards the sensor:
-
Foreshortening: slopes facing the radar look compressed and bright.
-
Layover: the top of a steep slope or tower returns before its base, and appears displaced towards the sensor.
-
Shadow: slopes facing away receive no signal and look black.
You can see the first of these in the hills in the lower left of the Sindh map, and the second in London’s towers. In both cases brightness reflects geometry, not material. In high mountains these are not details: along the Karakoram Highway large parts of every valley are in layover or shadow from one pass direction, which is why ascending and descending passes are combined and why such pixels are masked before any height or motion is read from them.
1.8 Wavelength: C band and L band¶
The wavelength decides what the radar interacts with. Sentinel-1’s C band (\(\lambda \approx 5.5\) cm) is scattered by leaves, twigs and small stones, so it sees the top of a canopy and the texture of a surface. NISAR’s L band (\(\lambda \approx 24\) cm, launched 2025) passes through leaves and is scattered by trunks, branches and the ground, so it sees deeper into vegetation. For interferometry this matters most: longer waves change less when leaves move or snow settles, so L-band images taken twelve days apart still match on slopes where C-band images have lost all phase coherence. In steep, vegetated, debris-covered mountains such as the Karakoram this is the difference between a usable measurement and noise.
1.9 Phase: what interferometry measures¶
Every radar pixel is a complex number: an amplitude (the backscatter used so far) and a phase, the fraction of a wavelength left over on the trip to the ground and back. One image’s phase looks random, because each pixel holds many scatterers. But two images of the same place taken from nearly the same orbit share that randomness, so multiplying one by the complex conjugate of the other cancels it and leaves the phase difference, the interferogram. That difference is a sum of contributions (Hanssen 2001):
Only the first three carry signal. The flat-earth term is a ramp from the curvature of the reference ellipsoid and is removed with the orbits. Which of the other two is wanted decides the job:
- Heights (a DEM). Choose a pair a few days apart, so the ground has not moved, with a large perpendicular baseline \(B_\perp\) (distance between the two orbits). The topographic phase gives height,
where \(R_0\) is slant range, \(\theta\) the look angle, and \(h_a\) the height of ambiguity: the height change that makes one full fringe. A larger baseline gives a smaller \(h_a\), finer height and denser fringes.
- Motion. Remove the topography with an existing DEM; what remains is motion along the line of sight,
There is no baseline in this equation: one fringe is half a wavelength of motion, 2.8 cm for Sentinel-1 and 12 cm for NISAR. That is why interferometry sees millimetres, and also why any DEM error or atmospheric delay leaks straight into apparent motion.
1.10 Unwrapping¶
The interferometer measures phase only modulo \(2\pi\): the true phase is the measured value plus an unknown whole number of cycles, which is why interferograms look like repeating rainbow fringes. Unwrapping recovers the missing cycles and turns the fringes into one continuous surface. The usual tool is SNAPHU (Chen and Zebker 2001), which finds the solution of lowest statistical cost over the whole image. Practical settings, which decide whether it works at all (Shah 2026b): use as few tiles as memory allows, because every seam between tiles is a place the solution can break; give tiles an overlap of 100 to 200 pixels (an overlap of zero leaves nothing to align and often gives an empty output); start with the minimum cost flow (MCF) method rather than a spanning tree; and set the cost mode to TOPO for heights and DEFO for motion. Unwrapping fails where coherence is low (water, snow, layover, fast change), so those pixels are masked, not guessed.
1.11 Polarimetry and covariance¶
A dual-polarised image gives two intensities, VV and VH (or HH and HV). A fully polarimetric radar also keeps the phase between polarisations, and the natural way to store that is a covariance matrix per pixel. NISAR’s geocoded covariance product (GCOV) does this (Shiroma et al. 2024): its diagonal terms (HHHH, HVHV, VVVV, VHVH) are the familiar powers, converted to decibels with \(10\log_{10}\), and are already terrain corrected (\(\gamma^0\)); the off-diagonal terms, when present, are complex and allow decompositions into surface, double-bounce and volume scattering (Freeman–Durden) or entropy, anisotropy and angle (Cloude–Pottier). One file can hold two frequency groups with different polarisations, and each comes with a mask: values 1 to 5 are valid (the sub-swath the data came from), 0 is invalid and 255 is outside the image. The gaps the mask leaves are a statement about quality and should be respected, not filled (Shah 2026a).
1.12 Reading rules¶
-
Dark usually means smooth, or facing away. It does not always mean water.
-
Bright usually means rough, wet, or a corner. It does not always mean buildings.
-
Compare like with like: the same pass direction and season.
-
Average in linear power, and report in dB.
-
Trust change between dates more than a single absolute value.